Erhan  Budak

Türkçe sürüm

Erhan Budak

E-mail : ebudaksabanciuniv.edu

Personal web page

Education :

B.Sc. and M.Sc. in Mechanical Engineering, Middle East Technical University (METU), 1987, 1989, respectively; Ph.D. in Mechanical Engineering, University of British Columbia (Canada), 1994.

Work Experience :

Pratt & Whitney (Canada), 1994-2000.

Areas of Interest :

Manufacturing processes and equipment; process modelling; monitoring and control; machine dynamics and mechanical vibrations.

Awards :

  • Vice Chair, Scientific and Tech. Committe on Machines - CIRP  2014
  • Fellow - CIRP  2011
  • Taylor Medal -  2003

Membership :

ASME CIRP

Publications :

Article
Yiğit, Ufuk and Ciğeroğlu, Ender and Budak, Erhan (2017) "Chatter reduction in boring process by using piezoelectric shunt damping with experimental verification", Mechanical Systems and Signal Processing, Vol.94, 312-321 ()
Özkırımlı, Ömer Mehmet and Tunç, Lütfi Taner and Budak, Erhan (2016) "Generalized model for dynamics and stability of multi-axis milling with complex tool geometries", Journal of Materials Processing Technology, Vol.238, 446-458 (SCI)
Aksu, Burak and Çelebi, Ceren and Budak, Erhan (2016) "An experimental investigation of oblique cutting mechanics", Machining Science and Technology, Vol.20, No.3, 495-521 (SCI)
Munoa, J. and Beudaert, X. and Dombovari, Z. and Altıntaş, Y. and Budak, Erhan and Brecher, C. and Stepan, G. (2016) "Chatter suppression techniques in metal cutting", CIRP Annals - Manufacturing Technology, Vol.65, No.2, 785-808 (SCI)
Tunç, Taner L. and Özkırımlı, Ömer Mehmet and Budak, Erhan (2016) "Machining strategy development and parameter selection in 5-axis milling based on process simulations", International Journal of Advanced Manufacturing Technology, Vol.85, No.5-8, 1483-1500 (SCI)
Tunç, Lütfi Taner and Budak, Erhan and Bilgen, Samet and Zatarain, Mikel (2016) "Process simulation integrated tool axis selection for 5-axis tool path generation", CIRP Annals - Manufacturing Technology, Vol.65, No.1, 381-384 (SCI)
Budak, Erhan and Özlü, Emre and Bakioğlu, Hayri and Barzegar Osgouei, Zahra (2016) "Thermo-mechanical modeling of the third deformation zone in machining for prediction of cutting forces", CIRP Annals - Manufacturing Technology, Vol.65, No.1, 121-124 (SCI)
Karagüzel, Umut and Uysal, Emre and Budak, Erhan and Bakkal, Mustafa (2016) "Effects of tool axis offset in turn-milling process", Journal of Materials Processing Technology, Vol.231, 239-247 (SCI)
Öztürk, Erdem and Çomak, Alptunç and Budak, Erhan (2016) "Tuning of tool dynamics for increased stability of parallel (simultaneous) turning processes", Journal of Sound and Vibration, Vol.360, 17-30 (SCI)
Özşahin, Orkun and Budak, Erhan and Özgüven, H. Nevzat (2015) "Identification of bearing dynamics under operational conditions for chatter stability prediction in high speed machining operations", Precision Engineering, Vol.42, 53-65 (SCI)
Aslan, Deniz and Budak, Erhan (2015) "Surface roughness and thermo-mechanical force modeling for grinding operations with regular and circumferentially grooved wheels", Journal of Materials Processing Technology, Vol.223, 75-90 (SCI)
Karagüzel, Umut and Olgun, Utku and Uysal, Emre and Budak, Erhan and Bakkal, M. (2015) "Increasing tool life in machining of difficult-to-cut materials using nonconventional turning processes", International Journal of Advanced Manufacturing Technology, Vol.77, No.9-12, 1993-2004 (SCI)
Karagüzel, Umut and Uysal, Emre and Budak, Erhan and Bakkal, Mustafa (2015) "Analytical modeling of turn-milling process geometry, kinematics and mechanics", International Journal of Machine Tools and Manufacture, Vol.91, 24-33 (SCI)
Tunç, Lütfi Taner and Özkırımlı, Ömer Mehmet and Budak, Erhan (2015) "Generalized cutting force model in multi-axis milling using a new engagement boundary determination approach", International Journal of Advanced Manufacturing Technology, Vol.77, No.1-4, 341-355 (SCI)
Özşahin, Orkun and Budak, Erhan and Özgüven, H. Nevzat (2015) "In-process tool point FRF identification under operational conditions using inverse stability solution", International Journal of Machine Tools and Manufacture, Vol.89, 64-73 (SCI)
Altıntaş, Y. and Kersting, P. and Biermann, D. and Budak, Erhan and Denkena, B. and Lazoğlu, I. (2014) "Virtual process systems for part machining operations", CIRP Annals - Manufacturing Technology, Vol.63, No.2, 585-605 (SCI)
Tunç, Lütfi Taner and Budak, Erhan (2013) "Identification and modeling of process damping in milling", Journal of Manufacturing Science and Engineering, Vol.135, No.2 (SCI)
Budak, Erhan and Çomak, Alptunç and Öztürk, Erdem (2013) "Stability and high performance machining conditions in simultaneous milling", CIRP Annals - Manufacturing Technology, Vol.62, No.1, 403-406 (SCI)
Tunç, Lütfi Taner and Budak, Erhan (2012) "Effect of cutting conditions and tool geometry on process damping in machining", International Journal of Machine Tools and Manufacture, Vol.57, 10-19 (SCI)
Budak, Erhan and Tunç, Lütfi Taner and Alan, Salih and Özgüven, H. Nevzat (2012) "Prediction of workpiece dynamics and its effects on chatter stability in milling", CIRP Annals - Manufacturing Technology, Vol.61, No.1, 339-342 (SCI)
Öztürk, Erdem and Tunç, Lütfi Taner and Budak, Erhan (2011) "Analytical methods for increased productivity in five-axis ball-end milling", International Journal of Mechatronics and Manufacturing Systems (IJMMS), Vol.4, No.3/4, 238-265
Özelkan, Ertunga C. and Öztürk, Özkan and Budak, Erhan (2011) "Identifying parameters of a broaching design using non-linear optimisation", International Journal of Modelling, Identification and Control (IJMIC), Vol.12, No.3, 244-252
Özkırımlı, Ömer M. and Budak, Erhan (2011) "Process simulation for five-axis machining for generalised milling tools", International Journal of Design Engineering, Vol.3, No.3, 232-246
Budak, Erhan and Öztürk, E. (2011) "Dynamics and stability of parallel turning operations", CIRP Annals - Manufacturing Technology, Vol.60, No.1, 383-386 (SCI)
Özlü, Emre and Molinari, Alain and Budak, Erhan (2010) "Two-zone analytical contact model applied to orthogonal cutting ", Machining Science and Technology, Vol.14, No.3, 323-343 (SCI)
Özşahin, Orkun and Özgüven, H. Nevzat and Budak, Erhan (2010) "Analysis and compensation of mass loading effect of accelerometers on tool point FRF measurements for chatter stability predictions", International Journal of Machine Tools and Manufacture, Vol.50, No.6, 585-589 (SCI)
Alan, Salih and Budak, Erhan and Özgüven, H. Nevzat (2010) "Analytical prediction of part dynamics for machining stability analysis", International Journal of Automation Technology , Vol.4, No.3, 259-267
Öztürk, Erdem and Budak, Erhan (2010) "Dynamics and stability of five-axis ball-end milling", Transactions of the ASME Journal of Manufacturing Science and Engineering, Vol.132, No.2 (SCI)
Budak, Erhan and Tunç, Lütfi Taner (2010) "Identification and modeling of process damping in turning and milling using a new approach", CIRP Annals - Manufacturing Technology, Vol.59, No.1, 403-408 (SCI)
Öztürk, Erdem and Tunç, Taner L. and Budak, Erhan (2009) "Investigation of lead and tilt angle effects in 5-axis ball-end milling processes", International Journal of Machine Tools and Manufacture, Vol.49, No.14, 1053-1062 (SCI)
Budak, Erhan and Tunç, Taner L. (2009) "A new method for identification and modeling of process damping in machining", Journal of Manufacturing Science and Engineering - Transactions of ASME, Vol.131, No.5 (SCI)
Özlü, Emre and Budak, Erhan and Molinari, A. (2009) "Analytical and experimental investigation of rake contact and friction behavior in metal cutting", International Journal of Machine Tools and Manufacture, Vol.49, No.11, 865-875 (SCI)
Tunç, Taner L. and Budak, Erhan (2009) "Extraction of 5-axis milling conditions from CAM data for process simulation", International Journal of Advanced Manufacturing Technology, Vol.43, No.5-6, 538-550 (SCI)
Özşahin, Orkun and Ertürk, Alper and Özgüven, H. Nevzat and Budak, Erhan (2009) "A closed-form approach for identification of dynamical contact parameters in spindle-holder-tool assemblies", International Journal of Machine Tools and Manufacture, Vol.49, No.1, 25-35 (SCI)
Budak, Erhan and Öztürk, Erdem and Tunç, Taner L. (2009) "Modeling and simulation of 5-axis milling processes", CIRP Annals - Manufacturing Technology, Vol.58, No.1, 347-350 (SCI)
Kayhan, Mehmet and Budak, Erhan (2009) "An experimental investigation of chatter effects on tool life", Proceedings of the Institution of Mechanical Engineers. Part B; Journal of Engineering Manufacture, Vol.223, No.11, 1455-1463 (SCI)
Budak, Erhan and Özlü, Emre (2008) "Development of a thermomechanical cutting process model for machining process simulations", CIRP Annals - Manufacturing Technology, Vol.57, No.1, 97-100 (SCI)
Çimren, Emrah and Çatay, Bülent and Budak, Erhan (2007) "Development of a machine tool selection system using AHP", The International Journal of Advanced Manufacturing Technology, Vol.35, No.3-4, 363-376 (SCI)
Özlü, Emre and Budak, Erhan (2007) "Analytical modeling of chatter stability in turning and boring operations - Part II: Experimental verification", Journal of manufacturing science and engineering, Vol.129, No.4, 733-739 (SCI)
Özlü, Emre and Budak, Erhan (2007) "Analytical modeling of chatter stability in turning and boring operations - part I: model development", Journal of Manufacturing Science and Engineering, Vol.129, No.4, 726-732 (SCI)
Ertürk, Alper and Budak, Erhan and Özgüven, H. Nevzat (2007) "Selection of design and operational parameters in spindle-holder-tool assemblies for maximum chatter stability by using a new analytical model", International journal of machine tools & manufacture, Vol.47, No.9, 1401-1409 (SCI)
Öztürk, Erdem and Budak, Erhan (2007) "Modeling of 5-axis milling processes", Machining science and technology, Vol.11, No.3, 287-311 (SCI)
Ertürk, A. and Özgüven, H. N. and Budak, Erhan (2007) "Effect analysis of bearing and interface dynamics on tool point FRF for chatter stability in machine tools by using a new analytical model for spindle-tool assemblies", International journal of machine tools & manufacture, Vol.47, No.1, 23-32 (SCI)
Ertürk, A. and Özgüven, H. N. and Budak, Erhan (2006) "Analytical modeling of spindle-tool dynamics on machine tools using Timoshenko beam model and receptance coupling for the prediction of tool point FRF", International Journal of Machine Tools and Manufacture, Vol.46, No.15, 1901-1912 (SCI)
Budak, Erhan (2006) "Analytical models for high performance milling. Part I: cutting forces, structural deformations and tolerance integrity", International Journal of Machine Tools and Manufacture, Vol.46, No.12-13, 1478-1488 (SCI)
Budak, Erhan (2006) "Analytical models for high performance milling. Part II: process dynamics and stability", International Journal of Machine Tools and Manufacture, Vol.46, No.12-13, 1489-1499 (SCI)
Budak, Erhan and Ertürk, A. and Özgüven, H. N. (2006) "A Modeling approach for analysis and improvement of spindle-holder-tool assembly dynamics", CIRP Annals - Manufacturing Technology, Vol.55, No.1, 369-372 (SCI)
Ertürk, Alper and Özgüven, H. Nevzat and Budak, Erhan (2006) "İşleme merkezlerinin dinamik analizi ve süreçte kararlılık: yeni bir analitik modelin uygulamaları", Makina Tasarım ve İmalat Dergisi, Vol.8, No.2, 55-66
Tekeli, Alper and Budak, Erhan (2005) "Maximization of chatter-free material removal rate in end milling using analytical methods", Machining science and technology, Vol.9, No.2, 147-167 (SCI)
Budak, Erhan and Lazoğlu, İsmail and Güzel, Birhan U. (2004) "Improving cycle time in sculptured surface machining through force modeling", CIRP Annals - Manufacturing Technology, Vol.53, No.1, 103-106 (SCI)
Kıvanç, Evren Burcu and Budak, Erhan (2004) "Structural modeling of end mills for form error and stability analysis", International Journal of Machine Tools and Manufacture, Vol.44, No.11, 1151-1161 (SCI)
Arslan, M. Çağdaş and Çatay, Bülent and Budak, Erhan (2004) "A decision support system for machine selection", Journal of Manufacturing Technology Management, Vol.15, No.1, 101-109
Budak, Erhan (2003) "An analytical design method for milling cutters with nonconstant pitch to increase stability, part 1: Theory", Journal of manufacturing science and engineering, Vol.125, No.1, 29-34 (SCI)
Budak, Erhan (2003) "An analytical design method for milling cutters with nonconstant pitch to increase stability, part 2: Application", Journal of manufacturing science and engineering, Vol.125, No.1, 35-38 (SCI)
Nemes, J. A. and Asamoah-Attiah, S. and Budak, Erhan (2001) "Cutting load capacity of end mills with complex geometry", CIRP Annals - Manufacturing Technology, Vol.50, No.1, 65-68 (SCI)
Wiercigroch, Marian and Budak, Erhan (2001) "Sources of nonlinearities, chatter generation and suppression in metal cutting", Philosophical transactions of the Royal Society of London series A - Mathematical physical and engineering sciences, Vol.359, No.1781, 663-693 (SCI)
Book Section / Chapter
Budak, Erhan, "CIRP Encyclopedia of Production Engineering (Chapter on machines)", CIRP Encyclopedia of Production Engineering, Laperrière, Luc and Reinhart, Gunther (eds.), NY: Springer, July 2014
Budak, Erhan, "Dynamic analysis and control", Machining Dynamics: Fundamentals, Applications and Practices, Cheng, Kai (ed.), London, England: Springer, January 2009, 21-84
Papers in Conference Proceedings
Azvar, Milad and Budak, Erhan, "Multi-dimensional modelling of chatter stability in parallel turning operation", 17th International Conference on Machine Design and Production, Atilim University, July 2016
Karagüzel, Umut and Bakkal, Mustafa and Budak, Erhan, "Modeling and measurement of cutting temperatures in milling", 7th CIRP Conference on High Performance Cutting (HPC 2016), Elsevier, June 2016, 173-176
Yılmaz, E. E. and Budak, Erhan and Özgüven, H. Nevzat, "Modeling and measurement of micro end mill dynamics using inverse stability approach", 7th CIRP Conference on High Performance Cutting (HPC 2016), Elsevier, June 2016, 242-245
Bakioğlu, Hayri and Özlü, Emre and Budak, Erhan, "Dik kesme modelinde üçüncü deformasyon bölgesi kuvvetlerinin termomekanik modellenmesi", Budak, Erhan (ed.), 6. Ulusal Talaşlı İmalat Sempozyumu, İstanbul: Sabanci University, November 2015
Hatipoğlu, Ersen and Budak, Erhan and Bakkal, Mustafa, "Mikro frezeleme işleminde yüzey oluşumunun modellenmesi", Budak, Erhan (ed.), 6. Ulusal Talaşlı İmalat Sempozyumu, İstanbul: Sabanci University, November 2015
Özşahin, Orkun and Budak, Erhan and Özgüven, Nevzat H., "Frezeleme esnasındaki tezgâh dinamiğinin belirlenmesi ve modellenmesi", Budak, Erhan (ed.), 6. Ulusal Talaşlı İmalat Sempozyumu, İstanbul: Sabanci University, November 2015
Yalçın, Turgut Köksal and Erberdi, Muharrem and Özlü, Emre and Budak, Erhan, "Yüksek hızlı iş millerinin termal modellemesi", Budak, Erhan (ed.), 6. Ulusal Talaşlı İmalat Sempozyumu, İstanbul: Sabanci University, November 2015
Putz, M. and Ihlenfeldt, S. and Karagüzel, U. and Semmler, U. and Budak, Erhan and Bakkal, Mustafa and Wertheim, R., "Improving performance of turn-milling by controlling forces and thermally induced tool-center point (TCP) displacement", Holger, Kohl and Seliger, Gunter and Mallon, Jurgen (eds.), 13th Global Conference on Sustainable Manufacturing: Decoupling Growth from Resource Use, Amsterdam: Elsevier, September 2015
Albayrak, Mehmet and Yalçın, Turgut Köksal and Erberdi, Muharrem and Özlü, Emre and Budak, Erhan, "Static and dynamic analysis of different machine tool spindles", Kaftanoğlu, Bilgin and Budak, Erhan (eds.), 8th International Conference and Exhibition on Design and Production of Machines and DIES/MOLDS, Ankara: Atilim University, June 2015
Bilgen, Samet and Özlü, Emre and Erberdi, Muharrem S. and Budak, Erhan, "An experimental study of CNC machine tool feed drive limits and cycle time prediction for a 3-axis milling operation", Kaftanoğlu, Bilgin and Budak, Erhan (eds.), 8th International Conference and Exhibition on Design and Production of Machines and DIES/MOLDS, Ankara: Atilim University, June 2015
Hatipoğlu, Ersen and Budak, Erhan and Bakkal, Mustafa, " Experimental investigation of tool wear in micro milling", Kaftanoğlu, Bilgin and Budak, Erhan (eds.), 8th International Conference and Exhibition on Design and Production of Machines and DIES/MOLDS, Ankara: Atilim University, June 2015
Bakioğlu, Hayri and Özlü, Emre and Budak, Erhan, "Thermo-mechanical modeling of cutting forces in micro endmilling operations", Altıntaş, Yusuf (ed.), 4th International Conference on Virtual Machining Process Technology, Canada, Vancouver, BC: UBC (University of British Columbia), May 2015
Çelebi, Ceren and Özlü, Emre and Budak, Erhan, "Experimental and analytical investigation of third deformation zone in orthogonal cutting", Altıntaş, Yusuf (ed.), 4th International Conference on Virtual Machining Process Technology, Canada, Vancouver, BC: UBC (University of British Columbia), May 2015
Karagüzel, Umut and Budak, Erhan and Bakkal, Mustafa, "Cutting temperature and tool wear in turn-milling", Altıntaş, Yusuf (ed.), 4th International Conference on Virtual Machining Process Technology, Canada, Vancouver, BC: UBC (University of British Columbia), May 2015
Aslan, Deniz and Kocaefe, Mert and Budak, Erhan, "Çevresel kanallı taşlar ile satıh taşlama operasyonunun modellenmesi (Modeling of surface grinding operation with circumferentially grooved wheels)", 5. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2014), Bursa, Türkiye: Uludağ Universitesi, November 2014
Baytok, Esma and Özlü, Emre and Budak, Erhan, "Titanyum ve alaşımlarının yüksek performanslı işlenmesi (High performance machining of titanium and its alloys)", 5. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2014), Bursa, Türkiye: Uludağ Üniversitesi, October 2014
Hatipoğlu, Ersen and Budak, Erhan, "Mikro frezeleme işleminde kesme parametrelerinin yüzey ve talaş oluşumuna etkisinin deneysel olarak incelenmesi (Experimental investigation of cutting parameters effect on surface generation and burr formation in micro milling)", 5. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2014), Bursa, Türkiye: Uludağ Universitesi, October 2014
Uysal, Emre and Karagüzel, Umut and Budak, Erhan and Bakkal, Mustafa, "Dik frezeyle tornalama işleminde eksenler arası ofsetin etkisi ve takım ömrü (Tool life and the effect of axis offset in orthogonal turn-milling)", 5. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2014), Bursa, Türkiye: Uludağ Universitesi, October 2014
Aslan, Deniz and Budak, Erhan, "Semi-analytical force model for grinding operations", 6th CIRP International Conference on High Performance Cutting (HPC2014), Amsterdam, Netherlands: Elsevier, June 2014, 7-12
Uysal, Emre and Karagüzel, Umut and Budak, Erhan and Bakkal, Mustafa, "Investigating eccentricity effects in turn-milling operations", 6th CIRP International Conference on High Performance Cutting (HPC2014), Amsterdam, Netherlands: Elsevier, June 2014, 176-181
Karagüzel, Umut and Olgun, Utku and Uysal, Emre and Budak, Erhan and Bakkal, Mustafa, "High performance turning of high temperature alloys on multi-tasking machine tools", Denkena, Berend (ed.), 4th Machining Innovations Conference, Switzerland: Springer 2014, 1-9
Yiğit, Ufuk and Ciğeroğlu, Ender and Budak, Erhan, "Chatter reduction in turning by using piezoelectric shunt circuits", Allemang, Randall and De Clerck, James and Niezrecki, Christopher and Wicks, Alfred (eds.), IMAC-XXXI Conference and Exposition on Structural Dynamics, New York: Springer 2014, 415-420
Aslan, Deniz and Budak, Erhan, "Satıh taşlama operasyonunda kuvvet ve sıcaklık modellemesi (Force and temperature modeling for surface grinding operation)", 4. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2013), Izmir, Turkey: Ege University 2013, 359-373
Baytok, Esma and Tuna, Başak and Toprak, Ayhan and Özlü, Emre and Budak, Erhan, "Freze ve delik delme işlemlerinde kullanılan karbür takımların sistematik olarak performans karşılaştırması (Performance comparison of milling and drilling carbide tools)", 4. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2013), Izmir, Turkey: Ege University 2013, 185-201
Çakır, Esin and Karagüzel, Umut and Olgun, Utku and Özlü, Emre and Bakkal, Mustafa and Budak, Erhan, "Dik kesme durumunda kesme sıcaklığının analitik modellenmesi ve deneysel olarak doğrulanması (Modeling of temperature distribution in orthogonal cutting and experimental verfication)", 4. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2013), Izmir, Turkey: Ege University 2013, 129-138
Çelebi, Ceren and Özlü, E. and Budak, Erhan, "Modeling and experimental investigation of edge hone and flank contact effects in metal cutting", 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO), Philadelphia, PA, USA: Elsevier 2013, 194-199
Çomak, A. and Koca, R. and Özkırımlı, Ö. M. and Budak, Erhan, "Modeling and simulation based design of variable pitch and variable helix milling tools for increased chatter stability", 7th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, -: Machines and Dies / Molds 2013
Çomak, Alptunç and Koca, Recep and Özlü, Emre and Özşahin, Orkun and Öztürk, Erdem and Tunç, Taner and Uysal, Emre and Budak, Erhan and Özgüven, H. Nevzat, "Talaşlı imalat süreçlerinin kararlılığı ve takım tezgah dinamiği (Machining process stability and machine tool dynamics)", Şakar, Gürkan (ed.), 16. Ulusal Makina Teorisi Sempozyumu (UMTS 2013), Erzurum, Turkey: Ataturk University 2013, 114-124
Koca, Recep and Budak, Erhan, "Optimization of serrated end mills for reduced cutting energy and higher stability", 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO), Philadelphia, PA, USA: Elsevier 2013, 570-575
Nizamoğulları, A. and Çomak, Alptunç and Budak, Erhan, "Paralel tornalama işlevini gerçekleştiren CNC torna tezgahının tasarımı, kesici uç ömrü ve kesme kararlılığı incelemeleri (Cutting tool life, cutting stability and process time review on designed and manufactured CNC turning machine which performs the parallel turning function)", 4. Ulusal Talaşlı İmalat Sempozyumu (UTİS 2013), Izmir, Turkey: Ege University 2013, 339-357
Olgun, Utku and Budak, Erhan, "Machining of difficult-to-cut-alloys using rotary turning tools", 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO), Philadelphia, PA, USA: Elsevier 2013, 81-87
Yasa, E. and Orhangül, A. and Songüler, S. C. and Platin, S. and Baytok, E. and Özlü, E. and Tunç, T. and Budak, Erhan, "Assessment of machinability performance in 5-axis milling of inconel 718 alloy with different carbide grades", 7th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, -: Machines and Dies / Molds 2013
Karagüzel, Umut and Bakkal, Mustafa and Budak, Erhan, "Process modeling of turn-milling using analytical approach", Shamato, Eiji (ed.), 3rd CIRP Conference on Process Machine Interactions (PMI), Amsterdam, Netherlands: Elsevier, November 2012, 131-139
Budak, Erhan, "Suppression of chatter vibrations in simultaneous machining operations", 15th International Machine Tool Engineers' Conference (IMEC), Tokyo, Japan: Japan Machine Tool Builders' Association, October 2012
Çomak, Alptunç and Budak, Erhan, "Eşzamanlı frezeleme operasyonlarının dinamiği ve kararlılığı", Şeker, Ulvi (ed.), 3. Ulusal Talaşlı İmalat Sempozyumu (UTIS 2012), Ankara, Türkiye: Gazi Üniversitesi, October 2012
Budak, Erhan, "Improving 5-axis milling operations using process models", Kolar, Petr (ed.), 9th International Conference on Machine Tools, Automation, Technology and Robotics (MATAR 2012), Prag, Czech Republic: MM Science Journal, September 2012
Özşahin, Orkun and Budak, Erhan and Özgüven, H. Nevzat, "Analytical modeling of the machine tool spindle dynamics under operational conditions", Hinduja, Srichand and Li, Lin (eds.), 37th International MATADOR Conference, Germany: Springer, July 2012, 117-122
Çomak, Alptunç and Budak, Erhan, "Chatter stability of parallel milling operations", 15. Uluslararası Makina Tasarım ve İmalat Kongresi (UMTİK 2012), Ankara, Turkey: METU (Middle East Technical University), June 2012
Özlü, Emre and Tunç, Lütfi Taner and Güven, İpek and Budak, Erhan, "Industrial applications of science integrated machining approach", Kılıç, Engin (ed.), 15. Uluslararası Makina Tasarım ve İmalat Kongresi (UMTİK 2012), Ankara, Turkey: METU (Middle East Technical University), June 2012
Çakır, Esin and Özlü, Emre and Bakkal, Mustafa and Budak, Erhan, "Modeling of temperature distribution in orthogonal cutting with dual-zone contact at rake face", 1st International Conference on Virtual Machining Process Technology (VMPT), Montreal, Canada: Ecole Polytechnic, May 2012
Tunç, Lütfi Taner and Budak, Erhan, "Effect of cutting conditions and tool geometry on process damping in machining", Bouzakis, K. (ed.), 4th International Conference on Manufacturing Engineering (ICMEN2011), Thessaloniki, Greece: Aristoteles University of Thessaloniki , October 2011
Özkırımlı, Ömer M. and Tunç, Taner L. and Budak, Erhan, "Simulation of multi-axis machining processes using z-mapping technique", Kaftanoğlu, Bilgin and Budak, Erhan (eds.), 6th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, Ankara, Turkey: Atılım University, June 2011
Özşahin, Orkun and Budak, Erhan and Özgüven, Nevzat H., "Investigating dynamics of machine tool spindles under operational conditions", Outeiro, J. C. (ed.), 13th CIRP Modeling of Machining Operations, Switzerland: Trans Tech Publications, May 2011, 610-621
Aran, Volkan and Budak, Erhan, "An experimental study on dynamics and stability of miniature end mills", Outeiro, J. C. (ed.), 13th CIRP Conference on Modelling of Machining Operations, Zurich, Switzerland: Trans Tech Publications 2011, 869-878
Akçay, Recep and Memiş, Emre K. and Özlü, Emre and Budak, Erhan, "Havacılık sanayinde süreç optimizasyonu için kararlılık diyagramlarının kullanımı", 2. Ulusal Talaşlı İmalat Sempozyumu (UTIS 2010), Konya, Türkiye: Selçuk Üniversitesi, October 2010
Öztürk, Erdem and Budak, Erhan, "Modeling dynamics of parallel turning operations", 4th CIRP International Conference on High Performance Cutting (HPC 2010), Paris, France: CIRP, October 2010
Tunç, Taner L. and Özkırımlı, Ömer Mehmet and Öztürk, Erdem and Murtezaoğlu, Yavuz and Budak, Erhan, "Machining strategy development in 5-axis milling operations using process models", 4th CIRP International Conference on High Performance Cutting (HPC 2010), Paris, France: CIRP, October 2010
Özkırımlı, Ömer Mehmet and Budak, Erhan, "Process simulation for 5-axis machining using generalized milling tool geometries", 14. Uluslararası Makina Tasarım ve İmalat Kongresi (UMTİK 2010), Ankara, Türkiye: Ortadoğu Teknik Üniversitesi, July 2010
Öztürk, Erdem and Budak, Erhan, "Tool orientation effects on the geometry of 5-axis ball-end milling", Hinduja, Srichand and Li, Lin (eds.), 36th International Matador Conference, Berlin, Germany: Springer, July 2010, 243-246
Akçay, Recep and Memiş, Emre K. and Özlü, Emre and Budak, Erhan, "Increasing productivity in high speed milling of airframe components using chatter stability diagrams", Altıntaş, Yusuf (ed.), 2nd International CIRP Conference on Process Machine Interactions (PMI 2010), Paris, France: CIRP, June 2010
Özlü, Emre and Engin, Şerafettin and Cook, Cristina and El-Wardany, Tahany and Budak, Erhan, "Simulation of broaching operations for tool design optimization ", 2nd International CIRP Conference on Process Machine Interactions (PMI 2010), Paris, France: CIRP, June 2010
Öztürk, Erdem and Budak, Erhan, "Modeling dynamics of parallel milling processes in time-domain", Altıntaş, Yusuf (ed.), 2nd International CIRP Conference on Process Machine Interactions (PMI 2010), Paris, France: CIRP, June 2010
Öztürk, Erdem and Özkırımlı, Ömer Mehmet and Süren, Gökhan and Budak, Erhan and Aksu, B., "Increasing productivity in die machining through process modelling", 5th International Conference and Exhibition on Design And Production of Machines And Dies/Molds, Kuşadası, Aydın, Türkiye: CIRP (International Academy for Production Engineering), June 2009
Özlü, Emre and Budak, Erhan, "Process modeling of orthogonal cutting with hone radiused tools ", 12th CIRP Conference on Modeling and Machining Operations, San Sebastian, Spain: CIRP (International Academy for Production Engineering) 2009
Özşahin, Orkun and Özgüven, H. Nevzat and Budak, Erhan, "Mass loading effect of accelerometers on tool point FRF and stability diagrams ", 12th CIRP Conference on Modeling and Machining Operations, San Sebastion, Spain: CIRP (International Academy for Production Engineering) 2009
Aksu, Burak and Özlü, Emre and Budak, Erhan, "Analysis and modeling of edge forces in orthogonal cutting", International Conference on Manufacturing Engineering, Greece:, September 2008
Budak, Erhan and Tunç, Taner L., "A new method for identification and modeling of process damping in machining", First International Conference on Process Machine Interactions, Hannover, Germany: Leibniz Universität , September 2008
Budak, Erhan and Çatay, Bülent and Tekin, İbrahim and Yenigün, Hüsnü and Abbak, Mehmet and Drannikov, Sergey and Şimşek, Oya, "Design of an RFID-based manufacturing monitoring and analysis system", RFID Eurasia, Istanbul: Istanbul Technical University, September 2007, 259-264
Budak, Erhan and Çatay, Bülent and Tekin, İbrahim and Yenigün, Hüsnü and Abbak, Mehmet and Drannikov, Sergey, "Microstrip patch antenna for RFID applications", RFID Eurasia, Istanbul, Turkey: Istanbul Technical University, September 2007, 265-267
Budak, Erhan, "Machining stability and machine tool dynamics", Ekinovic, S. (ed.), 11th International Research/Expert Conference " Trends in the Development of the Machinery and Associated Technology", Bosnia: Univ. of Zenica, August 2007
Özlü, Emre and Budak, Erhan and Molinari, Alain, "Thermomechanical modeling of orthogonal cutting including the effect of stick-slide regions on the rake face", Micari, Fabrizio and Filice, Luigino (eds.), 10th CIRP INternational Workshop on Modeling of Machining OPerations, Calabria, Italy: University of Calabria, August 2007
Öztürk, Erdem and Özlü, Emre and Budak, Erhan, "Modeling dynamics and stability of 5-axis milling processes", Micari, Fabrizio and Filice, Luigino (eds.), 10th CIRP INternational Workshop on Modeling of Machining OPerations, Calabria, Italy: University of Calabria, August 2007
Tunc, Taner and Budak, Erhan, "Optimization of 5-Axis milling processes based on the process models with application to airfoil machining", Micari, Fabrizio and Filice, Luigino (eds.), 10th CIRP International Workshop on Modeling of Machining OPerations, Calabria, Italy: University of Calabria, August 2007
Özlü, Emre and Budak, Erhan, "Experimental analysis and modeling of orthogonal cutting using material and friction models ", Kaftanoglu, Bilgin and Budak, Erhan and Akkok, Metin and Fırat, Mehmet (eds.), 4th International Conference and Exhibition on Machines and Design and Production of Dies and Molds, Ankara, Turkey: METU, June 2007
Özelkan, Ertunga and Öztürk, Özkan and Budak, Erhan, "Optimization of broaching design", Bayraksan, G. and Lin, W. and Son, Y. and Wysk, R. (eds.), 2007 Industrial Engineering Research Conference, USA: - 2007
Özlü, Emre and Budak, Erhan, "Analytical stability models for turning and boring operations", 2nd International Conference on High Speed Cutting,, June 2006
Özlü, Emre and Budak, Erhan, "Analytical prediction of stability limit in turning operations", CIRP International Workshop on Modeling of Machining Operations,, May 2006, 99-106
Tunç, L. Taner and Budak, Erhan and Öztürk, Erdinç, "Optimization of 5-axis milling processes using process models", 9th CIRP International Workshop on Modeling of Machining Operations,, May 2006, 179-186
Özlü, Emre and Budak, Erhan, "Tornalama işlemlerinde süreç kararlılığının analitik olarak modellenmesi", TİMAK Kongresi,, April 2006
Öztürk, Erdem and Budak, Erhan, "5 eksen frezelemede kuvvet ve şekil hatalarının modellenmesi", TIMAK Conference, Balıkesir: Balıkesir Üniversitesi, April 2006
Tunç, L. Taner and Budak, Erhan, "5 eksen frezeleme süreçlerinin modelleme yoluyla benzetimi ve eniyilenmesi", TIMAK Conference, Balıkesir: Balıkesir Üniversitesi, April 2006
Budak, Erhan and Tekeli, Erkin, "Maximizing chatter free material removal rate in milling through optimal selection of axial and radial depth of cut pairs", 55th General Assembly of CIRP, Bern, Switzerland: CIRP, July 2005, 353-356
Öztürk, Erdem and Budak, Erhan, "Modeling of 5-axis forces", Proceedings of the 8th International Workshop on Modeling of Machining Operations, Chemnitz, Germany: -, May 2005, 319-326
Budak, Erhan, "High performance milling", Aerotrends 2004 Conference,, July 2004
Kayhan, Mehmet and Budak, Erhan, "Investigating effects of chatter vibrations on tool wear in turning", 4th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering,, July 2004, 679-684
Köktürk, Utku and Budak, Erhan, "Optimization of broaching tool geometry", International Seminar on Intelligent Computation i, CIRP, July 2004, 393-398
Çimren, Emrah and Çatay, Bülent and Budak, Erhan, "Development of a machine tool selection system using analytic hierarchy process ", 4th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering (CIRP ICME '04), Paris, France: CIRP, May 2004, 193-198